K0FTT Automobiles

My position About ☰

reset

VK2LJ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2LJ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1765434052	13.21 Volts	39.32 Deg.C
1765433752	13.24 Volts	37.85 Deg.C
1765433452	13.21 Volts	37.85 Deg.C
1765433153	13.27 Volts	37.85 Deg.C
1765432853	13.21 Volts	37.85 Deg.C
1765432245	13.16 Volts	36.88 Deg.C
1765432069	13.36 Volts	36.88 Deg.C
1765431769	13.21 Volts	36.39 Deg.C
1765431469	13.21 Volts	35.9 Deg.C
1765430870	13.19 Volts	35.41 Deg.C
1765430570	13.16 Volts	34.92 Deg.C
1765430270	13.16 Volts	34.43 Deg.C
1765429970	13.19 Volts	34.43 Deg.C
1765429671	13.19 Volts	33.94 Deg.C
1765429071	13.24 Volts	33.94 Deg.C
1765428944	13.21 Volts	33.94 Deg.C
1765428918	13.27 Volts	33.94 Deg.C
1765428862	13.21 Volts	33.94 Deg.C
1765428678	13.3 Volts	34.43 Deg.C
1765428089	13.21 Volts	34.92 Deg.C
1765427705	13.19 Volts	35.41 Deg.C
1765427397	13.27 Volts	36.39 Deg.C
1765427314	13.24 Volts	36.39 Deg.C
1765427223	13.24 Volts	36.88 Deg.C
1765416311	13.51 Volts	32.48 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)