K0FTT Automobiles

My position About ☰

reset

W6SRR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6SRR-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	DC*	PC Board*	CPU*	Ambient*
1765337510	1354	74.2	32.7	68.1
1765336609	1353	74.3	33.2	68.3
1765335710	1354	74	33.2	68
1765334808	1354	73.8	32.7	68
1765333910	1353	74.1	32.7	68
1765333010	1353	74.2	33.2	68.2
1765332110	1351	74.2	33.2	68.2
1765331208	1354	74.1	32.7	68.2
1765330311	1353	74.2	33.2	68.2
1765329409	1353	74.2	33.2	68.3
1765328510	1354	74.2	32.7	68.3
1765327608	1353	74.1	33.2	68.3
1765326711	1354	74.1	32.7	68.3
1765325810	1354	74.1	33.2	68.2
1765324911	1347	73.8	33.2	68.1
1765324009	1347	73.7	33.2	68
1765323110	1353	73.6	32.2	67.9
1765322209	1353	73.5	32.2	67.7
1765321314	1354	73.5	32.7	67.6
1765320408	1353	73.3	32.2	67.4
1765319510	1354	73.2	32.2	67.4
1765318609	1353	73.1	32.2	67.2
1765317710	1354	72.8	32.2	67.1
1765316808	1354	72.7	32.2	66.9
1765315911	1353	72.6	32.2	66.8

*Used Equation Coefficients:

DC: 0, 1, 1000

PC Board: 0, 0.1, 0

CPU: 0, 0.1, 0

Ambient: 0, 0.1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)