K0FTT Automobiles

My position About ☰

reset

DC4HF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC4HF-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1765373713	617	5688	7436	3724	4532
1765372812	617	5688	7436	3730	4529
1765371911	617	5694	7438	3738	4522
1765371010	617	5695	7439	3744	4517
1765370109	617	5694	7436	3750	4499
1765369208	617	5701	7440	3758	4480
1765368307	617	5707	7438	3769	4461
1765367406	617	5710	7435	3781	4439
1765366505	617	5732	7439	3795	4404
1765365604	617	5738	7442	3816	4355
1765364704	617	5737	7442	3875	4206
1765363802	617	6638	7441	3988	3890
1765362893	617	5693	7436	3729	4422
1765361992	617	5692	7436	3743	4408
1765361091	617	5696	7436	3688	4538
1765360190	617	5699	7435	3679	4522
1765359289	617	5701	7438	3673	4513
1765358388	617	5703	7437	3668	4506
1765357487	617	5709	7438	3666	4502
1765356586	617	5708	7437	3665	4496
1765355685	617	5716	7437	3666	4471
1765354784	617	5718	7436	3673	4426
1765353883	617	5734	7436	3685	4398
1765352982	617	5736	7439	3699	4371
1765352081	617	5741	7441	3717	4338

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)