This is the latest recevied telemetry packets stored in our database for station/object SA2KLM-97. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Voltage* | Celsius* | Rel_Hum* | Atm_Press* | Value5* |
|---|---|---|---|---|---|
| 1766134594 | 4.12 VDC | 22.2 C | 36.86 % | 1004.63 hPa | 0 |
| 1766129753 | 4.14 VDC | 22.3 C | 36.85 % | 1003.75 hPa | 0 |
| 1766106479 | 4.09 VDC | 22.3 C | 36.49 % | 995.38 hPa | 0 |
| 1766101235 | 4.1 VDC | 22.3 C | 36.46 % | 999.63 hPa | 0 |
| 1766093502 | 4.11 VDC | 22.2 C | 36.95 % | 995.63 hPa | 0 |
| 1766087403 | 4.12 VDC | 22.1 C | 36.57 % | 999.63 hPa | 0 |
| 1766082743 | 4.14 VDC | 21.9 C | 36.33 % | 995.25 hPa | 0 |
| 1766076116 | 4.16 VDC | 21.9 C | 36.39 % | 998.88 hPa | 0 |
| 1766072645 | 4.17 VDC | 22 C | 35.1 % | 999 hPa | 0 |
| 1766071373 | 4.19 VDC | 22.2 C | 34.79 % | 1002.38 hPa | 0 |
| 1766068042 | 4.19 VDC | 22.9 C | 34.14 % | 1001 hPa | 0 |
| 1766063039 | 4.09 VDC | 21.8 C | 34.6 % | 998.88 hPa | 0 |
| 1766054869 | 4.09 VDC | 22 C | 33.26 % | 1001.25 hPa | 0 |
*Used Equation Coefficients:
Voltage: 0, 0.01, 0
Celsius: 0, 0.1, -50
Rel_Hum: 0, 0.01, 0
Atm_Press: 0, 0.125, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)